STMicroelectronics MW Series EEPROM are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for STMicroelectronics . Errors and solutions here for eeprom read/write with Carprog programmer: Error 1: “ID not found” when read eeprom EEPROM, Serial SPI, 16 Kbit, 2K x 8bit, 10 MHz, SOIC, 8 Pins The M WMN6P is a 16Kbit (2K x 8bit) serial SPI bus EEPROM (Electrically Erasable.

Author: Yozshugor Mulkis
Country: Cameroon
Language: English (Spanish)
Genre: Love
Published (Last): 8 August 2018
Pages: 82
PDF File Size: 7.89 Mb
ePub File Size: 11.14 Mb
ISBN: 603-6-39426-864-2
Downloads: 64011
Price: Free* [*Free Regsitration Required]
Uploader: Mujas

Once the chip is blank, then you can load your data file and click on Write button to wrtie the data into chip. Reply 14 benaknoun Spain Posts. You can save data as. Reply 17 ZLM Posts. Reply 5 ZLM Posts. That is safe and fastest way. Reply 3 ZLM Posts. It should be 59160 to open it by same software.

Reply 1 ZLM Posts. Which part number you selected in software? What is your another adapter part number? The only way to test data is: But the fast way is to remove it from board and program it on the programmer ZIF spcket directly. Also, another question please about the same chip: When you uploading the image, only use letter and number as file name. What is exact part number?


Use ToolA instead, because your chip pins already damaged.

MCUmall EPROM BIOS Chip Burner Forum – 8pin

Reply 2 benaknoun Spain Posts. All other pins are pin to pin connect to programmer socket. Hi, deprom have received the tools i bought from mcumall canada, there are numbers on the adapters, how do i know which pin is the right matching one with the chip?

Reply 9 ZLM Posts.

Try to power up the board and do not connect pin 8 Vcc pin. Reply 15 ZLM Posts.

Carprog 9.31 reads/writes eeprom 95160 with A4/A6 adapter

Reply 13 benaknoun Spain Posts. Hi, it seems i’m doing something right then! What is your chip on board? The wire can be any wires, eepron long as you can solder it. Reply 8 benaknoun Spain Posts.

Reply 12 ZLM Posts. Reply 6 benaknoun Spain Posts. I believe they will do the job. Reply 7 ZLM Posts. The “Device blank check failed ” means the chip is not a blank chip, there are some data in the chip. It is SOIC8 mil chip. Reply 4 benaknoun Spain Posts. Reply 10 benaknoun Spain Posts. Reply 19 ZLM Posts. That is eeprm on your circuit design.


Hi, i have connected the tool to the chip and adapter to the programmer. Reply 18 benaknoun Spain Posts. Also, when i click on ID, it eeprrom “function not supported on this device” Image Insert: Then the ADP should be used. To be honest though, the other adapter i bought, not sure what its for?? You need to find a way to test the data. Hi, thanks for your reply, here are the numbers on the chip: Reply 11 benaknoun Spain Posts.

I think it should be SOIC8 mil chip. Most of used on-board chips should have something. Hi, ok forget this chip, its damaged If the chip is not designed for programming in circuit, then you need to try to find some connection. Chip is blank does this mean this chip is empty??? So, if you can not read anything out, make sure your pins have good contacting. Device blank check failed at address: If it is “”, then it has no ID on this chip.

Reply 951160 benaknoun Spain Posts.